Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя

Страница: 33 / 49

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

The Step Back controls the amount which the blades retract after cutting the wire

PLEASE ENTER

insulation and before pulling the insulation off the wire. Example: After running a test

STEP BACK DISTANCE

wire through the Model 93 you see that the inner conductor has been scraped. You

STEP BACK =

would now enter a value(.001”-.050”) to retract the blades so that a clean strip can be

obtained.

IMPORTANT

: There is a big difference between “nicking” and “scrapping”

the inner conductors of the wire. Nicking is when the blades cut to deep into the

insulation, and is observed right at the shoulder of the stripped wire. Scraping is

observed not at the shoulder of the strip, but along the length of the inner conductor as

the insulation slug is stripped from the wire. Nicking is corrected using the

Blade Strip

Depth

feature and scrapping is corrected using the

Step Back

feature. Press

ENTER.

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

FLAT CABLE MODE

cont.

LCD DISPLAY PROMPT

ACTION REQUIRED

PLEASE ENTER BLADE

The Model 93 will default to Blade Speed 1 when in the Flat Cable Mode. You may

SPEED(1 THRU 4)

accept or change this value. Press

ENTER

DEFAULT IS 1

SPEED

Press

FEED SPEED

key. This setting determines the speed of the wire passing

through the machine.

PLEASE ENTER FEED

Select 1-slow, 2-slow/medium, 3-medium, 4 -fast. Press

ENTER.

SPEED (1 THRU 4)

NOTE:

When selecting speed 1 or 2 the maximum Pull Speed that can be selected is

SPEED =

Press

PULL SPEED

key. This setting determines the pull force of insulation being

removed.

PLEASE ENTER PULL

Select pull speed 1(maximum pulling force),2 & 3(medium pulling force),

SPEED (1 THRU 5)

4 & 5(minimum pulling force). Press

ENTER.

SPEED =

Press

AMOUNT

key. This value is the number of wires to be processed. Also allows

access to Multiple Batch Processing mode.

CHANGE

CURRENT

NOTE:

If using the multiple batch feature; during initial programming this entry can

AMOUNT

be ignored and proceed to next screen. During the actual processing this screen may

OR PRESS ENTER

be used to change the current batch total without affecting any subsequent batches.

PLEASE ENTER

The batch feature allows you to process required pieces in a single or multiple

NUMBER OF BATCHES

batch(es). To process required pieces in one batch enter “1”. Press

ENTER

RUN

To process total amount in multiple batches, enter number of batches to process.

Press

ENTER

FEED

SPEED

PULL

SPEED

AMOUNT

Содержание Compu-Strip 93


















































Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды

Carpenter MFG. Co., Inc. Compu-Strip 93, Руководство оператора

Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды