Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 23

Страница: 23 / 49

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

UNLOADING WIRE

Unload wire by pressing the

UNLOAD WIRE

key. Wire will automatically feed backwards through machine as long as the

key is depressed.

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

WINDOW STRIP MODE

The Model 93 is equipped with a Window Strip Mode feature. It is very

IMPORTANT

that all dimension values be entered

in the sequence shown or an error message will display. When the Window Strip Mode is activated the Red LED next to
the WINDOW MODE sample, on the Front Panel, will light.

LCD DISPLAY PROMPT

ACTION REQUIRED

CARPENTER MFG.

Press

ENTER.

MODEL 93 COMPU STRIP

VERSION

PLEASE PRESS ENTER

Press

TRAILING STRIP

key. This value is the length of insulation to be stripped from

the left end (trailing end) of wire.

0.00

Enter dimension. Press

ENTER.

PLEASE

ENTER

TRAIL STRIP LENGTH

PLEASE

ENTER

Enter number of strip steps. Press

ENTER.

NUMBER OF PULL STEPS

NOTE:

The same notes and warning under

PLEASE ENTER NUMBER OF PULL

STEPS = 1

STEPS

on Page 11 apply to this set up also. Please reread them.

Press

TRAILING PULL

key. This value is the distance the slug of insulation is pulled

on the trailing end of the wire

0.00

Enter dimension. For a full strip enter a value greater than the overall trailing strip

PLEASE ENTER

length. For a partial strip enter a value less than the overall trailing strip length.

TRAIL PULL LENGTH

Press

ENTER

Press

WIRE LENGTH

key. This value is the overall length of pieces being processed.

0.00

Enter dimension. Press

ENTER.

PLEASE ENTER
OVERALL WIRE LENGTH

Press

LEADING STRIP

key. This value is the length of insulation to be stripped from

the right end (leading end) of the wire.

UNLOAD

WIRE

TRAILING

STRIP

TRAILING

PULL

WIRE

LENGTH

LEADING

STRIP

Содержание Compu-Strip 93


















































Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды

Carpenter MFG. Co., Inc. Compu-Strip 93, Руководство оператора

Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды