Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя

Страница: 13 / 49

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

NORMAL MODE

cont.

LCD DISPLAY PROMPT

ACTION REQUIRED

Press

LEADING STRIP

key. This value is the length of insulation to be stripped from

the right end (leading end) of the wire.

0.00

Enter dimension. Press

ENTER.

PLEASE

ENTER

LEAD STRIP LENGTH

PLEASE

ENTER

Enter number of strip steps. Press

ENTER.

NUMBER OF PULL STEPS

NOTE:

The same notes and warning under

PLEASE ENTER NUMBER OF PULL

STEPS = 1

STEPS

on the previous page, apply to this set up also. Please reread them.

Press

LEADING PULL

key. This

value is the distance the slug of insulation is

pulled on the leading end of the wire.

0.00

Enter dimension. For a full strip enter a value greater than the overall leading strip

PLEASE

ENTER

length. For a partial strip enter a value less than the overall leading strip length.

LEAD PULL LENGTH

Press

ENTER.

Press

BLADE DEPTH

key. This key allows access to answer questions about the wire

being processed. Ex. Wire Type, Wire Gauge, Strip Depth, Stepback, Blade Speed,

Guide Tube Size.

SELECT WIRE TYPE

Use the number keys to select wire type. Arrow will indicate current setting.

1 – SOLID (S)

Press

ENTER.

When Flat Cable is selected proceed to Page 30 for specific

2 – STRANDED (M)

programming

instructions.

3 – FLAT (F)

PLEASE ENTER WIRE

Enter wire gauge of cable, 32 to 12 gauge. Press

ENTER.

GAUGE HERE OR STRIP

NOTE: If processing multi conductor or flat cable proceed to next screen.

DEPTH ON NEXT MENU

WIRE GAUGE=

PLEASE ENTER LEAD

The Model 93 will default to a preset nominal blade depth based upon wire gauge

BLADE STRIP DEPTH

previously entered. You may accept this or change according to cable being

processed.

PRESS ENTER

To open blades enter a higher value and to close blades enter a lower value.

STRIP DEPTH =

To process multi conductor cable enter strip depth dimension based upon overall

dimension of inner conductors. Press

ENTER.

LEADING

STRIP

LEADING

PULL

BLADE

DEPTH

Содержание Compu-Strip 93


















































Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды

Carpenter MFG. Co., Inc. Compu-Strip 93, Руководство оператора

Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды