BMW K 1200RS страница 97 Скачать руководство пользователя

Страница: 97 / 416

11.11

1100

Preparatory work with engine

installed

1100

…for removal of combined oil/

water pump

–

Remove the right side section of the fairing
(

46.8).

–

Remove the engine spoiler (

46.14).

–

Drain coolant (

00.67).

1100

…for removal of timing case

cover, removal of timing chain

Important:

Disconnect ground lead from battery and insulate.

–

Remove left and right fairing side sections
(

46.8).

–

Remove the engine spoiler (

46.14).

•

Detach the radiators at left and right from their
holders and press forwards.

…for removal of cylinder head, removal
of piston with conrod

Important:

Disconnect ground lead from battery and insulate.

–

Remove left and right fairing side sections
(

46.8).

Warning:

Comply with safety regulations; fuel lines are pres-
surised.

–

Remove fuel tank (

16.5).

–

Remove the engine spoiler (

46.14).

•

Remove exhaust system (

18.5).

•

Remove fuel injection rail (

13.7).

•

Remove throttle-valve rail together with intake air
silencer.

•

Detach the engine from the front cross-member
at the left.

•

Disconnect the temperature sensor plug at the
cylinder head and run the cable through down-
wards.

•

Remove left/right radiators with fans (

17.7).

•

Disconnect the coolant hoses from the coolant
stub pipes.

1100

…for removal of crankshaft

–

Remove the right side section of the fairing
(

46.8).

…for removal of intermediate flange,
removal of output shaft

–

Remove engine (

11.12).

…for checking valve clearances,
adjusting valve clearances

•

Remove left side section of fairing (

46.8).

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды

BMW K 1200RS, Руководство по ремонту

Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды