BMW K 1200RS страница 363 Скачать руководство пользователя

Страница: 363 / 416

46.29

46 00

Lifting frame

Note:

Valid for the following tasks only:
Removing starter/alternator
Removing clutch/gearbox
Removing engine

Remove battery

(

00.69).

•

Remove the seat.

–

Remove the tool tray.

–

Remove the battery retaining plate.

Important:

Disconnect the negative battery terminal first, then
the positive terminal.

–

Remove the battery

Remove fairing.

–

Remove left and right fairing side sections
(

46.10).

–

Remove the air inlet guide (

46.17).

–

Remove the intake air pipe (

46.17).

–

Remove the engine spoiler (

46.14).

–

[Option pannier case carrier]

Loosen the left/

right pannier case carrier at the front.

–

Remove the left/right rear side sections
(

46.15).

–

Remove the front section of the rear carrier (front
section of rear wheel splash guard) and discon-
nect the plug for the power socket (

46.7).

Unfasten the exhaust system.

•

Release the retaining hoop at the silencer.

[Additional work for removing engine]
Remove exhaust system

(

18.5).

•

Drain engine oil.

•

Disconnect the oil cooler pipes at the intermedi-
ate oil pump flange.

•

Release clamp for oil cooler line from engine
spoiler bracket.

Remove fuel tank

(

16.5).

–

Disconnect the plug for the immersion-tube sen-
sor.

–

Disconnect the plug for the fuel pump.

Warning:

Comply with safety precautions when handling or
working with fuel.

–

Disconnect the fuel lines.

–

Release the tank cover fastener.

–

Release the fuel tank fasteners at the frame and
take off the fuel tank.

Remove throttle-valve rail complete with intake
air silencer.

•

Disconnect the plug for the temperature sensor
at the intake air silencer.

•

Release the hose clips for the intake stub pipes,
noting the correct installed position.

•

Pull off the throttle-valve rail complete with intake
air silencer.

Note:

Do not disconnect the throttle cable.

•

Disconnect the hose connection for the crank-
case breather at the crankcase.

•

Disconnect plug for throttle-valve actuator and
plug for switch of cruise-control systems.

•

Secure the throttle-valve rail together with the in-
take air silencer to the frame.

Take off the fuel injection rail.

•

Disconnect the plug for the throttle-valve poten-
tiometer.

•

Disconnect the earth (ground) cable at the throt-
tle-valve rail.

•

Disconnect the fuel hoses at the fuel injection
rail.

•

Disconnect the vacuum hose for the throttle-
valve rail at the fuel injection rail.

Note:

Do not disconnect the throttle cable.

•

Remove the injection rail and secure to frame,
complete with wiring harness, throttle-valve rail
and intake silencer.

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды

BMW K 1200RS, Руководство по ремонту

Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды