BMW K 1200RS страница 128 Скачать руководство пользователя | Manualshive

Страница: 128 / 416

background image

11.42

•

Place the bearing cap in position and tighten the
screws to the specified torque.

L

Note:

The crankshaft must not be turned any more.

•

Use an angle-of-rotation gauge,

BMW No. 11 2 500

, to tighten the big end

bearings.

X

Tightening torque:

Conrod bearings .......................................... 20 Nm
Additional angle of rotation................................ 80°

•

Unscrew the big end cap again and remove it.

•

Use the comparison scale (arrow) to determine
bearing play.

Bearing play 0.030…0.066 mm (0.0012...0.0026 in)
Wear limit .............................. 0.130 mm (0.0051 in)

•

When renewing the bearing shells, make sure
that the colour marks on the crankpins and big
end bearings match.

•

Regrinding stages

“0”

and

“1”

are available; the

crankpins are marked with a corresponding
number of paint spots.

•

The absence of paint spots identifies the grind-
ing stage as

“0”

.

L

Note:

The crankshaft can only be reground in stage

“0”

,

and must be hardened and finished afterwards.

1100

Checking dimensions of crank-

shaft

•

If measurement reveals that bearing clearance is
excessive, the crankshaft must be measured.

–

Grinding stages “0” and “1” are available; the
crankshaft is marked with the appropriate
number of paint spots at the bearing journal.

Colour code at timing end of crankshaft:

Grinding stage 1 at crankshaft bearing journal (1).
Grinding stage 1 at crankpin (2).
The absence of paint spots identifies the grinding
stage as “0”.

L

Note:

Only a crankshaft marked as grinding stage “0” can
be ground,

Crankshaft dimensions............. see Technical Data.

–

Grinding must be followed by heat treatment and
finishing before the crankshaft is reinstalled.

•

When renewing the bearing shells, make sure
that the colour marks on the crankpins and big
end bearings match.

KR110630

KL110290

2

1

«
...
126
127
128
129
130
...
»

Содержание K 1200RS

































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K 1200RS

Бренд: KYMCO Страницы: 58

Бренд: N-Com Страницы: 36

Бренд: R&G Страницы: 21

Бренд: R&G Страницы: 24

Бренд: Honda Страницы: 28

Бренд: Triumph Страницы: 53

Бренд: R&G Страницы: 27

Virago XV1100K(C)

Бренд: Yamaha Страницы: 111

Бренд: Yamaha Страницы: 101

Бренд: hepco & becker Страницы: 2

Бренд: PMI Страницы: 2

Бренд: hepco & becker Страницы: 6

Бренд: Ducati Страницы: 27

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

TOPMASTER H0PC10ST

Бренд: Shad Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды