BMW K 1200RS страница 111 Скачать руководство пользователя

Страница: 111 / 416

11.25

Assembling pistons and conrods

Important:

It should be possible to push the piston pin through
the small end bushing with only slight pressure.

•

Note weight tolerances when replacing conrods:
use only conrods of the same weight class.

Weight tolerance ........................... ± 4 g (0.141 oz.)

•

Weigh the conrods to determine the weight
class.

Note:

Coloured spots on the conrod indicate the weight
class.

Note:

The oil bore in the conrod eye is on top in the in-
stalled position. The arrow on the piston crown must
point in the forward direction of travel.

•

Only install pistons of the same weight group.

•

Check the marks on the piston crowns (arrow) to
determine the weight class.

Important:

Always use two new wire circlips per piston pin
when reassembling.

•

Assemble piston and conrod.

Weight class codes for conrods

Class

Weight in g (oz.) Colour coding

413 ... 416.9
(14.579...14.717)

2 x white

417 ... 420.9
(14.720...14.858)

2 x blue

421 ... 424.9
(14.861...14.999)

3 x white

425 ... 428.9
(15.003...15.140)

3 x yellow

429 ... 432.9
(15.144...15.281)

1 x blue

Weight classes, pistons without piston rings

Weight of piston
in g (oz.)

189 ...195
(6.672...6.884)

195 ... 210
(6.884...7.413)

Marking

KL110310

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды

BMW K 1200RS, Руководство по ремонту

Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды