BMW K 1200RS страница 143 Скачать руководство пользователя

Страница: 143 / 416

12.8

12 11

Timing the ignition

–

Remove the spark plugs.

–

Remove the cover from the Hall-effect transmit-
ter.

–

[With Motronic]

Remove the left side section of

the fairing (

46.15).

–

[Without Motronic]

Remove the fuel tank

(

16.5).

•

[Without Motronic]

Open the lid of the electron-

ic equipment box.

•

Screw dial gauge,

BMW No. 00 2 580

, with ex-

tension into cylinder 1.

•

Set the piston to TDC.

•

Set the dial gauge scale ring to “0”.

•

Turn the engine back in a clockwise direction
(normal direction of engine rotation is anti-clock-
wise) until the piston is at the firing point.

Setting:

Ignition firing point.......... 6° before TDC = 0.24 mm

........................................... (0.0094 in) before TDC

•

[With Motronic]

Connect

BMW

MoDiTeC to di-

agnosis plug.

•

[Without Motronic]

Connect

BMW

MoDiTeC to

plug connector (6) on the Hall-effect transmitter.

•

Start the “Timing ignition” program at the

BMW

MoDiTeC.

•

Loosen the fasteners of magnetic gate (1) and
turn it to the left or right until the

BMW

MoDiTeC

displays the correct ignition firing point.

Adjusting ignition timing:

Turn counter-clockwise....................... retard timing
Turn clockwise ................................ advance timing

•

Retighten magnetic gate (1).

•

Check that ignition timing is correct.

–

Turn the engine in its normal direction of rotation.
With the piston at 0.24 mm (0.0094 in) before
TDC, the

BMW

MoDiTeC must display the cor-

rect ignition firing point.

•

Installation is the reverse of the removal proce-
dure.

Tightening torque:

Magnetic gate ................................................ 6 Nm
Spark plugs.................................................. 20 Nm

KR120020

00 2 580

KR120050

KR120060

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды

BMW K 1200RS, Руководство по ремонту

Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды