BMW K 1200RS Скачать руководство пользователя страница 287

Страница: 287 / 416

33.18

33 11

Shimming housing cover

•

In order to obtain the correct taper roller bearing
preload, the housing cover must be correctly
shimmed.

•

Using depth gauge, measure distance “a”.

•

Place measuring ring,

BMW No. 33 2 601

, in po-

sition and secure it.

•

Measure from the outer ball bearing race through
the cutout in the measuring ring to the housing
mating face and determine distance “b”.

–

Distance “a” – distance “b” = shim thickness
(without preload).

•

Lightly grease the shim of the selected thick-
ness, and place it on the crown wheel.

Preload:

............ 0.05...0.1 mm (0.0020...0.0039 in)

33 11

Installing housing cover

Note:

Checking/adjusting the ABS sensor gap is required
after replacement of the following components:
–

Cover of rear wheel drive housing

–

Crown wheel.

•

Oil the shaft sealing ring (31) slightly.

•

Using drift,

BMW No. 33 1 860

, and handle,

BMW No. 00 5 500

, drive in shaft sealing ring (1).

Important:

Do not overheat shaft sealing ring and cord ring
seal.

•

Lightly oil/grease the cord ring seal and insert it.

•

Heat the housing cover to 60 °C (140 °F) and
place it on the crown wheel.

•

Tighten retaining bolts in diagonally opposite se-
quence.

Tightening torque:

Housing cover to housing ............................ 35 Nm

KR330290

KR330300

33 2 601

KR330310

00 5 500

33 1 860

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

BMW K 1200RS, Руководство по ремонту, Страница: 287 / 416

Результаты поиска

Содержание K 1200RS

Отзывы: