BMW K 1200RS страница 251 Скачать руководство пользователя

Страница: 251 / 416

31.14

31 42

Assembling telescopic fork

Note:

Traces of oil on the surface can be interpreted as
leaks.

•

If necessary, remove oil from under the sealing
boot.

Important:

Check that copper washer is correctly seated.

•

Install oil drain plug with new copper washer.

•

Fill with oil.

Capacity per fork leg

.................................... 0.51 l

Oil grade

........................

BMW telescopic-fork oil

Tightening torque:

Oil drain plug................................................ 13 Nm

Note:

No routine maintenance is needed, and therefore
the fork oil does not have to be changed during In-
spections.

•

Install fixed tube.

•

Install washer.

•

Oil shaft sealing ring lightly and press it home on
sliding tube (1), using the combined weight (ar-
row) of drift,

BMW No. 31 5 610

, reducing adapt-

er with lugs,

BMW No. 31 5 613

, and sleeve,

BMW No. 31 5 614

•

Install retaining ring.

•

Install fixed fork tube.

•

Install wiper.

31 42

Measuring telescopic fork

Warning:

After an accident, always examine the telescopic
fork for cracks and signs of damage.

31 00

Check slider tube bridge

Important:

Replace distorted slider tube bridge.

•

Check smoothness of slider tube bridge.

31 00

Checking the fixed fork tube for

runout

•

Place both ends of fixed fork tube in V-blocks.

•

Turn fixed fork tube slowly and measure it with a
dial gauge,

BMW No. 00 2 510

Important:

Do not straighten distorted fixed fork tubes: always
replace them.

Maximum permissible runout

. 0.4 mm (0.0157 in)

31 5 610

KR310100

31 5 614

31 5 613

KL310030

00 2 510

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды

BMW K 1200RS, Руководство по ремонту

Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды