BMW K 1200RS Скачать руководство пользователя страница 374

Страница: 374 / 416

51.3

51 25

Removing/installing ignition

switch/steering lock

–

Remove fork bridge (

31.9).

•

Secure fork bridge in retaining fixture,

BMW No. 31 5 670

•

Using an 4 mm (0.1575 in) drill bit, drill the heads
of the non-removable screws to a depth of
approx. 5 mm (0.1969 in).

•

Using an 8 mm (0.3150 in) drill bit, drill away the
heads of the non-removable screws.

•

Remove the washers.

•

Remove ignition switch/steering lock.

•

Unscrew the threaded pins with a stud remover.

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

•

Tighten the non-removable screws with steering
lock socket wrench insert,

BMW No. 51 0 531

Tightening torque:

Non-removable screw .................................. 15 Nm

51 25

Removing/installing lock barrel

Remove the lock barrel

Note:

The lock barrel can also be removed when the fork
bridge is installed.

–

Turn the ignition key to the ON position.

•

Press in the safety catch by inserting a suitable
tool through the opening (arrow), e.g. a piece of
wire.

•

Pull the lock barrel out with the ignition key.

Removing lock barrel if ignition key has broken
off

Important:

When drilling (without removing the fork bridge) trap
the swarf which is formed.

•

Using a 4-5 mm (0.1575-0.1969 in) drill bit, open
up the entire length of the lock barrel.

•

Repeat with a drill bit of larger diameter until the
lock barrel can be removed.

Installing lock barrel

•

Grease new lock barrel with

Shell Retinax EP2

•

Insert the lock barrel with the key in the ON posi-
tion.

•

Press the lock barrel down with the key until the
keeper engages.

•

Grease the opening (arrow) for the keeper with

Shell Retinax EP2

and close it.

31 5 670

KR510010

KR510030

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

BMW K 1200RS, Руководство по ремонту, Страница: 374 / 416

Результаты поиска

Содержание K 1200RS

Отзывы: