manualshive.com logo in svg

BMW K 1200RS, Руководство по ремонту

BMW K 1200RS Repair Manual is a comprehensive guide for maintaining and repairing your motorcycle. You can easily download it for free from manualshive.com. Этот руководство поможет вам узнать все, что вам нужно знать о BMW K 1200RS и как его ремонтировать.

Поделиться
Скачать
background image

00.17

Contents

Page

00

General view of crated motorcycle 

.................................................................................. 19

Checking the shipping crate for damage 

.....................................................................20

Damage discovered in Germany

 ............................................................................................20

Damage discovered in importer markets

 ............................................................................20

Unpacking the motorcycle 

....................................................................................................21

General instructions 

.................................................................................................................21

Pushing the motorcycle onto a workshop platform

 .......................................................21

Inspecting motorcycle for damage 

..................................................................................21

Checking that delivery is complete 

..................................................................................21

Installing remaining items on motorcycle 

....................................................................22

Installing the windscreen

 ...........................................................................................................22

Installing mirrors, left/right

 .........................................................................................................22

Installing bracket for engine spoiler

 ......................................................................................23

Installing the engine spoiler

 ......................................................................................................23

Filling and charging the battery 

.........................................................................................24

Remove the battery  ...........................................................................................................................24
Filling and charging the battery ..........................................................................................................24
Installing the battery  ..........................................................................................................................24

Checking tyre pressures 

........................................................................................................25

Checking tightness of rear wheel studs 

........................................................................25

Checking and adjusting the motorcycle 

........................................................................26

Checking the function of side stand contact switch

 .....................................................26

Checking the headlight beam setting and adjusting if necessary

 ..........................26

Vertical adjustment  ............................................................................................................................26
Lateral adjustment .............................................................................................................................26

Installing the seat

 ..........................................................................................................................27

Adjusting seat

 .................................................................................................................................27

Adjusting the handlebars, left/right

 .......................................................................................27

00 Pre-delivery check

Содержание K 1200RS

































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K 1200RS

S&B Filters 76-6000 Installation Instructions Manual preview
76-6000
Бренд: S&B Filters Страницы: 7
KTM 990 Adventure Baja Owner'S Manual preview
990 Adventure Baja
Бренд: KTM Страницы: 227
N-Com basic kit 2 User Instructions And Safety preview
basic kit 2
Бренд: N-Com Страницы: 32
TREND AIRPRO MAX User Instructions preview
AIRPRO MAX
Бренд: TREND Страницы: 38
KTM 525 XC Owner'S Manual preview
525 XC
Бренд: KTM Страницы: 207
URAL Motorcycles cT 2022 Owner'S Manual preview
cT 2022
Бренд: URAL Motorcycles Страницы: 104
TM 2008 4 Stroke User Manual preview
2008 4 Stroke
Бренд: TM Страницы: 80
Shad HONT72SF Quick Start Manual preview
HONT72SF
Бренд: Shad Страницы: 2
Shark Vancore Manual preview
Vancore
Бренд: Shark Страницы: 16
RIEJU Marathon 125 AC EURO 4 Owner'S Manual preview
Marathon 125 AC EURO 4
Бренд: RIEJU Страницы: 45
RIEJU MRT 50 EURO 5 Owner'S Manual preview
MRT 50 EURO 5
Бренд: RIEJU Страницы: 52
APRILIA SR 50 Manual preview
SR 50
Бренд: APRILIA Страницы: 151
Benelli TRK 502 2017 Owner'S Manual preview
TRK 502 2017
Бренд: Benelli Страницы: 469
Petzl EIOS-3 Manual preview
EIOS-3
Бренд: Petzl Страницы: 10
Abus Mount K Instruction Manual preview
Mount K
Бренд: Abus Страницы: 35
APRILIA PEGASO 650 I.E. STRADA Use And Maintenance Book preview
PEGASO 650 I.E. STRADA
Бренд: APRILIA Страницы: 96
X-lite X-702 Safety And Instructions For Use preview
X-702
Бренд: X-lite Страницы: 80
Honda Magna VF750C Owner'S Manual preview
Magna VF750C
Бренд: Honda Страницы: 112

Бренды по названию

Популярные бренды

Загрузить еще бренды