BMW K 1200RS страница 58 Скачать руководство пользователя | Manualshive

Страница: 58 / 416

background image

00.49

Change the rear brake fluid/bleeding

e

Attention:

During the replacement process, the brake fluid
level must not drop below the hose level or else air
will be drawn into the brake system.

d

Warning:

If the brake-fluid level in the reservoir does fall below
hose level, the wheel circuit must be refilled at the
brake caliper and bled once again (

a

34.17).

•

Draw off the old brake fluid from the wheel-circuit
reservoir (4).

•

Undo the fasteners on the wheel circuit
reservoir (4).

•

Screw the filler bottle,

BMW No. 34 1 581

, onto

the rear wheel circuit reservoir.

•

Slowly fill the filler bottle,

BMW No. 34 1 581

, to

approximately 1/3 its capacity with new brake
fluid.

•

Wrap a cloth around the brake caliper.

•

Connect the brake bleeding device to the bleed
screw, but

do not switch on

the unit.

•

Switch on the ignition.

L

Note:

After switching on the ignition, always wait for the
BMW Integral ABS to complete its self-diagnosis.
Do not operate the brake lever until self-diagnosis
has completed.

•

Very gently press the footbrake lever until the
pump just starts up.

•

Open the bleed screw while topping up the filler
bottle with new brake fluid as necessary.

•

Pump out the brake fluid with virtually no pressu-
re to begin with, then vary the brake pressure.

L

Note:

The higher the brake pressure the faster the fluid is
pumped through the system, which means that the
level in the wheel-circuit reservoir drops all the more
rapidly.

•

When the brake fluid is clear and free of bubbles,
continue to pump off brake fluid just until no
more fluid is visible in the filler bottle.

•

Close the bleed screw.

•

Release the brake lever and switch off the igniti-
on.

•

Disconnect the brake bleeding device from the
bleed screw.

•

Remove the filler bottle from the wheel circuit re-
servoir.

•

Top up the wheel-circuit reservoir to the

MAX

mark.

e

Attention:

After changing and/or bleeding the brakes, always
top up the fluid in the wheel-circuit reservoir to the
correct level in accordance with the instructions.

•

Fill rear wheel-circuit reservoir with brake fluid in
accordance with instructions (

a

00.50).

e

Attention:

After all the work on the brake system has been
completed, run a bleed test using the

BMW

MoDiTeC!

•

Perform bleed test with

BMW

MoDiTeC

(

a

00.35).

X

Tightening torque:

Bleed screw to brake caliper ........................ 10 Nm

Brake fluid

...................................................DOT 4

K41000100

MIN

MAX

4

34 1 581

«
...
56
57
58
59
60
...
»

Содержание K 1200RS

































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K 1200RS

Бренд: Yamaha Страницы: 32

Бренд: Suzuki Страницы: 440

SBL.04.650.10000/B

Бренд: SW-Motech Страницы: 2

Бренд: Triumph Страницы: 53

GRIZZLY 90 2020

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 166

Бренд: Yamaha Страницы: 452

Бренд: Yamaha Страницы: 132

Бренд: Shark Страницы: 16

Бренд: Norton Страницы: 69

LEDV46-T-TS LIGHT KIT

Бренд: AdMore Lighting Страницы: 4

Бренд: Smarter tools Страницы: 28

EMPORIO ARMANI 946 2015

Бренд: VESPA Страницы: 416

Бренд: R&G Страницы: 2

Бренд: R&G Страницы: 9

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды