BMW K 1200RS Скачать руководство пользователя страница 248 | Manualshive

Страница: 248 / 416

BMW K 1200RS Скачать руководство пользователя страница 248

31.11

31 42

Removing/installing slider tube

bridge

–

Remove the engine spoiler and holder
(

a

46.14).

•

Secure lifter,

BMW No. 00 1 510

, to oil sump.

e

Important:

Do not operate the handbrake lever when the brake
calipers have been removed. Protect painted parts
from scratching: apply adhesive masking tape if
necessary.

–

Remove front wheel (

a

36.5).

–

Remove left and right fairing side sections
(

a

46.8).

–

Remove front mudguard (

a

46.6).

–

Remove/install steering damper (

a

31.17).

–

Remove protective cap of leading link fastener.

e

Important:

Screw is secured with a thread-locking compound.

L

Note:

Support the slider tubes.

•

Release the fastener for the leading link at slider
tube bridge (1) with the socket wrench insert and
internal hexagon,

BMW No. 31 5 600

.

e

Important:

Screw is secured with a thread-locking compound.

•

Undo the fasteners (arrows) at slider tube
bridge (1).

e

Important:

Make sure that brake line and front sensor cable are
not stretched when telescopic fork extends. Sup-
port the slider tubes.

•

Extend the telescopic fork.

•

Remove slider tube bridge (1).

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

•

Install front quick-release axle.

e

Important:

When installing, use a new screw.

•

Tighten the fasteners (arrows) at slider tube
bridge (1).

e

Important:

When installing, use a new nut.

•

Tighten the leading link fastener to fork slider
tube bridge (14), using socket wrench insert and
internal hexagon,

BMW No. 31 5 600

.

X

Tightening torque:

Leading link to slider tube bridge
(clean  apply Loctite 2701) ............ 130 Nm
Steering damper to leading link ..................  21 Nm
Slider tube bridge to telescopic fork
(clean  apply Loctite 243) ................ 21 Nm

KR310070

1

31 5 600

KR310210

1

«
...
246
247
248
249
250
...
»

Содержание K 1200RS

































































































































































































































































































































































































































Отзывы:

Нет отзывов