manualshive.com logo in svg

BMW K 1200RS, Руководство по ремонту, Страница: 119 / 416

Поделиться
Скачать
BMW K 1200RS Скачать руководство пользователя страница 119

11.33

1100  

Removing output shaft

Removing oil sump

•

Take out the screws.

•

Loosen the gasket with light blows of a plastic-
faced hammer and take off the oil sump.

Removing the oil mesh strainer and oil filter

•

Take out the screw and pull off oil mesh 
strainer (1).

•

Remove the O-ring for the oil mesh strainer (ar-
row) from the lower part of the crankcase.

•

Unscrew oil filter (2) with oil filter wrench, 

BMW No. 11 4 650

.

Removing lower part of crankcase

•

Remove the screws securing the lower part of 
the crankcase.

•

Remove screws (4) for the shouldered bearing 
and screws (3) for the needle roller bearing.

•

Loosen the gasket with light blows of a plastic-
faced hammer, and take off the lower part of the 
crankcase. Note the O-rings for the water and oil 
passages.

•

Carefully lift out the output shaft; the needle roller 
bearing and circlip are loose on the shaft.

Replacing oil level sight glass

•

Pierce the plastic disc with a large screwdriver 
and lever out the oil level sight glass.

•

Use thinners to remove all traces of oil from the 
seating face of the sight glass.

•

Coat the sealing face of the new oil level sight 
glass with tyre assembly paste and drive it in with 
drift, 

BMW No. 00 5 550

.

KR110440

1

2

4

3

Содержание K 1200RS

































































































































































































































































































































































































































Отзывы:

Нет отзывов