BMW K 1200RS Скачать руководство пользователя страница 354

Страница: 354 / 416

46.20

46 50

Removing/installing main

stand/side stand

46 53

Disassembling and assembling

side stand

•

Disengage the tension springs and take off the
plate with the springs.

–

Remove switch for side stand (arrow)
(

61.16).

•

Remove the side stand.

•

Installation is the reverse of the removal proce-
dure.

Important:

Install screw and nut with

Loctite 243

Lubricant:

for bushing .................................. Shell Retinax EP2

Tightening torque:

Side stand to pivot mount
(clean apply Loctite 243) ................ 41 Nm
Switch to side stand
(clean apply Loctite 243) .................. 9 Nm

46 52

Removing/installing pivot mount

with centre (main) and side stands

–

Remove the seat (

52.5).

–

Remove the engine spoiler (

46.14).

–

Remove engine spoiler holder (

46.14).

•

Secure lifter,

BMW No. 00 1 510

, to oil sump.

•

Raise the motorcycle until the centre stand can
move freely.

•

Disconnect the cable tie, disconnect the plug for
the side stand switch and guide the cable
through downwards.

•

Remove the screws (arrows) holding the pivot
mount.

•

Installation is the reverse of the removal proce-
dure.

Tightening torque:

Pivot mount to gearbox ................................ 41 Nm

46 52

Removing/installing main (centre)

stand (

00.71)

KR460260

KR460250

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

BMW K 1200RS, Руководство по ремонту, Страница: 354 / 416

Результаты поиска

Содержание K 1200RS

Отзывы: