BMW K 1200RS страница 225 Скачать руководство пользователя

Страница: 225 / 416

23.17

23 12 Assembling output shaft

Note:

Assembly starts at the shift
gearwheel for 4th gear (9). Before assembly, oil all
friction faces lightly with gear oil.

•

Clamp the output shaft into the vise with soft
jaws and with the splines facing upwards.

•

Install circlip (6/arrow).

•

Install thrust washer (7).

Important:

To avoid damaging the needle roller bearings on the
splines when installing, spread the rollers carefully
at the end faces.

•

Install needle roller bearing (8).

•

Install shift wheel for 4th gear (9) with the pockets
facing circlip (6).

•

Install support washer (10) and needle roller
bearing (11).

•

Install shift wheel for 3rd gear (12) with pockets
facing away from the 4th gear shift wheel (9).

•

Install backup washer (13) and circlip (14).

•

After installing, measure endplay at 3rd and 4th
gear shift wheels.

•

Install shift wheel for 5th gear (15) with recess for
shift fork facing towards the 3rd gear shift wheel
(12).

•

Install backup washer (1) and needle roller bear-
ing (2).

•

Install shift wheel for 1st gear (3) with the pockets
facing towards the 5th gear shift wheel (15).

•

Install spacing washer (4) and grooved ball bear-
ing (5).

–

After installing, check endplay at 1st gear shift
wheel (

23.19).

KR230120

18 17

KR230130

Содержание K 1200RS

































































































































































































































































































































































































































Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды

BMW K 1200RS, Руководство по ремонту

Результаты поиска

Содержание K 1200RS

Отзывы:

Похожие инструкции для K 1200RS

Бренды по названию

Популярные бренды