Berger Lahr WDP3-01X Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 114

background image

3.8

On-line command processing via serial or field bus interface

This mode is available if the unit has a serial interface RS 232 or RS 485
or a field bus interface (e.g. Interbus-S or Profibus-DP) installed in
adapter slot OPT.1.

Only available for

some unit variants;

see chapter 3.1.

In this mode, single movement commands and other commands are
transmitted to the controller and executed immediately. A comprehensive
command set is available for this purpose.

NOTE
The following parameters must have been set (see chapter 3.3.1):
– For serial interface, operating mode with parameter P00 = 2
– For CAN-Bus, operating mode with parameter P62
– Network address with parameter P60 (only for RS 485, Profibus-DP,
CAN-Bus and SUCONET)
– Baud rate with parameter P61 (only for serial interface, Interbus-S and
CAN-Bus)

If “run” is displayed in the status display, on-line command processing is
enabled.
Start by activating the power controller with the INITDRIVE command
before executing any movement commands.

ATTENTION
The parameters set via the front panel are used for the basic
settings of the unit. Some of these settings can be changed by
on-line command processing.
The transmitted values will be lost when switching off.

Reference documentation

On-line command processing mode is described in the following do-
cumentations:

–

On-line Command Processing and Upload/Download via Serial
Interface

–

On-line Command Processing via CAN-Bus

–

On-line Command Processing via Interbus-S

–

On-line Command Processing via Profibus-DP

–

On-line Command Processing via SUCONET

Description of the P69 parameter

If the parameter P69 = 1, a manual movement via I/O (see chapter 3.4)
and status output via outputs (see chapter 4.1) is possible.
During a manual movement (signal AUTOM = 0), only read commands
can be processed.

On-line

command

processing

Operation

WDP3-01X Ident. no.: 00441109760

3-23

«
...
73
74
75
76
77
...
»

Содержание WDP3-01X



















































































































Отзывы:

Нет отзывов

Похожие инструкции для WDP3-01X

Бренд: jbc Страницы: 4

Бренд: Jafar Страницы: 10

Бренд: Fanimation Страницы: 2

Бренд: M2M Страницы: 24

Бренд: Samson Страницы: 32

Бренд: Quantum Страницы: 15

Бренд: Samson Страницы: 40

Бренд: Vanderbilt Страницы: 2

Бренд: X-lander Страницы: 72

Бренд: X Rocker Страницы: 38

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

Бренд: YASKAWA Страницы: 30

Бренд: Vag Страницы: 15

Бренд: tell Страницы: 11

SUPERSTAR E-3000/F2

Бренд: praher Страницы: 10

Бренд: IDEC Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды