Berger Lahr WDP3-01X Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 114

background image

1.2.3

Principle of a reference
movement

When executing a reference movement, a reference point is approached
which is defined as the zero point for the system of dimensions. All
subsequent absolute positioning operations refer to this zero point.

Reference movements can be made towards the CCW limit switch, CW
limit switch and the reference switch.
The reference movement is executed at reference speed REF_IN (par-
ameter P06). The shaft moves away from the limit or reference switch at
reference speed REF_OUT (parameter P07).

Figures 1-9 and 1-10 illustrate the principles of various reference move-
ments.

Reference speed REF_IN

Reference speed REF_OUT

M

CCW

limit switch

CW

limit switch

CCW limit switch
reference point

CW limit switch
reference point

Max. allowed
dist. limit switch

Fig. 1-9 Principle of reference

movement to limit switch

Reference speed REF_IN

Reference speed REF_OUT

CCW

limit switch

CW

limit switch

Case 1

Case 2

Reference switch
reference point

Max. allowed
dist. limit switch

Reference

switch

M

Fig. 1-10 Principle of reference

movement to reference switch

General description

WDP3-01X Ident. no.: 00441109760

1-11

«
...
17
18
19
20
21
...
»

Содержание WDP3-01X



















































































































Отзывы:

Нет отзывов

Похожие инструкции для WDP3-01X

Бренд: XBOX Страницы: 2

Бренд: Vacon Страницы: 64

Бренд: Calsense Страницы: 74

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: Ebyte Страницы: 35

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 8

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Бренд: Nedap Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды