Berger Lahr WDP3-01X Скачать руководство пользователя страница 44

Страница: 44 / 114

2.4.6

RS 485 serial interface

(OPT.1)

NOTE
The RS 485 serial interface is installed in adapter slot 21; see type plate.

NOTE
The serial interface is a four-wire interface.

Solder the litz wires to the connector as illustrated in fig. 2-15.

Pin

Signal

Meaning

1, 6

12VDC

MP 923 supply voltage

→

2, 7

GND

MP 923 supply voltage ground

→

TXD

Inverted transmitted data

→

RXD

Inverted received data

←

SGND

Signal ground

TXD

Transmitted data

→

RXD

Received data

←

Input

→

Output

Push the shield back and fix with a cable tie.

Insert two threaded bolts (fig. 2-16) into the connector shell.

Place the connector into the connector shell.

Fasten the cable and the shield to the connector shell with screws,
providing for strain relief.

ATTENTION
Ensure good electrical contact between the shield and the con-
nector shell.
Connect the shield on both ends.

Assemble the two parts of the connector shell with two screws.

Fasten the connector to the front panel (item 21) with screws.

NOTE
For a PC with RS 232 interface, the MP 923 interface converter can be
used (see chapter 6.2.3).

NOTE
The MP 924 interface distributor can be used for controlling eight units
(see chapter 6.2.4).

21
OPT.1

Installation

2-18

WDP3-01X Ident. no.: 00441109760

Содержание WDP3-01X



















































































































Результаты поиска

Содержание WDP3-01X

Отзывы:

Похожие инструкции для WDP3-01X

Бренды по названию

Популярные бренды

Berger Lahr WDP3-01X, Руководство пользователя

Результаты поиска

Содержание WDP3-01X

Отзывы:

Похожие инструкции для WDP3-01X

Бренды по названию

Популярные бренды