Berger Lahr WDP3-01X Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 114

background image

1.2

Function

1.2.1

Hardware components

The actual function of the controller depends on the configuration of the
interface adapter slots OPT.1 and OPT.2.

The following configuration options are available:

Interface configuration

for OPT.1 and OPT.2

Interface

adapter slot

Device functions

OPT.1

OPT.2

Not

installed

Not

installed

Oscillator mode or position processing
via inputs/outputs

–

Position processing via inputs/outputs
or front panel, or oscillator mode via
inputs/outputs (can be set with front
panel parameter P00)

–

Manual mode via inputs/outputs or front
panel

–

Teach-in mode via inputs/outputs or
front panel

–

Position and parameter input via front
panel

RS 422

–

Rotation monitoring, if parameter
P20 = 2 and P00

≠

3

RS 232

or

RS 485

Not

installed

Position processing via inputs/outputs or
on-line command processing via serial
interface

Position processing or on-line command
processing (can be set with front panel
parameter P00):

–

In position processing mode, the unit
has the same scope of functions as
the basic unit, except oscillator mode
via inputs/outputs. In addition,
positions and parameters can be
uploaded and downloaded via the
serial interface.

–

In on-line command processing mode,
the unit has the same scope of
functions as the unit with field bus
interface.

RS 422

–

Rotation monitoring, if parameter
P20 = 2 and P00

≠

3

–

Electronic gear,
If P00 = 3, the gear parameters are
input via the front panel or a download
via the serial interface.
If P00 = 2, the gear parameters are
input using on-line command
processing via serial interface.

General description

1-2

WDP3-01X Ident. no.: 00441109760

«
...
8
9
10
11
12
...
»

Содержание WDP3-01X



















































































































Отзывы:

Нет отзывов

Похожие инструкции для WDP3-01X

Бренд: Vacon Страницы: 62

Бренд: Ohsung Electronics Страницы: 18

Бренд: Bard Страницы: 8

Бренд: Bardiani Valvole Страницы: 35

Бренд: Eaton Страницы: 288

Бренд: Magellan Страницы: 2

Бренд: Radware Страницы: 98

Бренд: RabbitCore Страницы: 34

Бренд: R82 Страницы: 11

Бренд: u-blox Страницы: 28

Бренд: u-blox Страницы: 2

Бренд: Union Instruments Страницы: 63

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA SIEMENS Страницы: 373

Бренд: Balboa Water Group Страницы: 88

Бренд: ABB Страницы: 2

Simply Smart PY75 A Series

Бренд: BABYTREND Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды