Berger Lahr WDP3-01X Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 114

background image

Profibus-DP network

Standardized field bus for data exchange in automation technology.
The Profibus-S standard can be used for interconnecting several
devices from different manufacturers and with different function-
ality through one uniform interface.
A Profibus-DP network may consist of several masters and
several slaves. Data exchange is effected by a cyclic transmission
method.

Pulse/direction signals

Signals for reference variable input for an electronic gear.

Reference movement

Motor movement towards the CCW or CW limit switch or a
reference switch for setting a reference point for the system of
dimensions.

Reference point

Position value after a reference movement or after setting the
reference point.

Reference speed

The reference speed is the speed at which the axis moves away
from a limit switch.

Reference switch

A switch which can be approached from either direction for a
reference movement.

Relative (incremental) positioning

For incremental positioning, the position value refers to the current
position of the axis.

Rotation monitoring

Rotation monitoring is used for detecting positional deviations of
motor movements. The actual position is detected by an encoder
and then compared with the setpoint. If the difference between
actual and set position exceeds a preset value, a contouring error
is reported and the motor is decelerated.

RS 485 interface

Serial interface for a network configuration.

Teach-in

The teach-in function is used for storing positions which have been
approached by manual control.

Upload

The upload function is used for reading data from the controller.

Appendix

6-14

WDP3-01X Ident. no.: 00441109760

«
...
104
105
106
107
108
...
»

Содержание WDP3-01X



















































































































Отзывы:

Нет отзывов

Похожие инструкции для WDP3-01X

Бренд: Hansen Страницы: 4

Бренд: Ransburg Страницы: 49

Бренд: Balboa Страницы: 2

Бренд: Badger Meter Страницы: 20

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

disklavier DKC-850

Бренд: Yamaha Страницы: 2

Бренд: POLA Страницы: 2

Бренд: Abocom Страницы: 10

Бренд: bihl+Wiedemann Страницы: 16

Tracer CH.530 RLC-SVU01B-E4

Бренд: Trane Страницы: 60

Бренд: Desoutter Страницы: 74

Бренд: jablotron Страницы: 2

Бренд: HANYOUNG NUX Страницы: 4

MXI-Express Gen-3 x16

Бренд: National Instruments Страницы: 38

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 7

StarSign Bio Token 3.0 M

Бренд: Giesecke & Devrient Страницы: 28

Бренд: Heat Controller Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды