BelFox 47-21-i, Руководство по установке

Страница: 90 / 288

42
STP Stop input open (actuated) SL7 Ts 27 & 28
LS Light barrier input open (actuated) SL7 Ts. 29 & 30
SE1 Safety input 1 - none 8,2kΩ detected / OES error SL8 Ts 32 & 35
SE2 Safety input 2 - none 8,2kΩ detected / OES error SL8 Ts 33 & 36
E-A Limit switch open detected
E-Z Limit switch Closed Detected
#### No learning trips carried out yet
? End positions / reference positions are searched
for after voltage is switched back on.
* Hold-up time is running out
13.4. Troubleshooting instructions
The DCM 21-i control unit make troubleshooting much easier for the
installer. The display not only shows you the currently activated inputs, but the
controls also have a memory, which stores the last 10 malfunctions (software)
see instruction point 13.1. and the last 50 activations (safety inputs etc.) – see
instruction point 13.2. incl. time display.
Proceed as follows to read out the currently actuated inputs:
Press the "Escape/Menu" key repeatedly until the display shows "Last com-
mands". Now press the "Escape/Menu" key again.
Now the current status of the motor is shown in the first line of the display. The
second line of the display shows you the currently activated/operated inputs.
Indicator
Significance of the indi-
cator
Potential malfunctioning Cause & remedy
Z1
&
Z2
The contacts of the hall
sensors, which are in-
stalled in the motor,
are active during en-
gine operation. They
flash continually in that
period.
In downtime, it has no
importance to know if
they are
active or not.
If they stopped flashing:
► The motor is defective
Replace the motor
►
The wire of the hall sensor is damaged
Repair the wire / replace the
motor
REF The Reed contact which
serves as a reference
point should shortly
flashes by each travel.
It stopped flashing: ► Magnet on the gear rack missing
Fix a new magnet
► The Reed contact is defective
43
Repair the wire / replace it
► The wire of the Reed contact is damaged
Repair the wire or replace the Reed
contact
It flashes continuously
►
The Reed contact is not connected
Connect the Reed contact
► The Reed contact is defective
Replace it
A
B
C
D
The inputs, which are
operated with poten-
tial-free buttons, flash
when they are active.
Though an external button
has been pressed, they do
not flash no more
► The circuit of the button is discontinuous
Repair the wire / replace it
► The button is defective
Replace the button
They flash continuously ► The wire is damaged
Repair the wire / replace it
► The button is defective
Replace the button
► A commutator has been set up instead of
a push-button
Set up a push-button
STP The stop input flashes
when the terminals 27
& 28 are not intercon-
nected
(Emergency stop
active)
Though the emergency
stop switch has been acti-
vated, the sign does not
flash.
►
The wire is damaged
Repair the wire / replace it
► Several emergency-stop switches have
been connected in parallel
Connect them in series
Though the emergency
stop switch has not been
activated,
It flashes continuously
► The wire of the emergency stop switch is
defective
Repair the wire / replace it
► the opening contact and the closing con-
tact of the emergency stop switch inter-
changed
Use a rest contact
LS The input of the light
barrier flashes if the
terminals 29 & 30 are
inter-connected. (Light
barrier active)
Though the light beam has
been interrupted, they do
not flash.
► The wire is pulled
Repair the wire / replace it
► Several light barriers have been connected
in parallel
Connect them in series
Though the light beam has
not been interrupted, they
flash
continuously.
► The wire of the safety contact edge is de-
fective
Repair the wire / replace it
► The opening contact and the closing con-