Belarus 1221.2 Скачать руководство пользователя

Страница: 271 / 295

BELARUS-1221.2/1221V.2/1221.3 Scheduled maintenance

270

Operation 40. Change filter elements of

fine fuel filter

•

Unscrew the plug (1) and discharge

sediment.

•

Unscrew the four nuts and remove

the cover (3).

•

Rinse the housing and cover with

pure diesel fuel.

•

Check the cover seal and, if

necessary, replace it.

•

Install a new filter element.

•

Fill the filter housing with fuel.

•

Install the cover and tighten the

fastening nuts.

IMPORTANT!

After cleaning or

replacing the filter element (or after full

consumption of fuel from the tanks), it is

necessary to bleed air from the system

before you start the engine.

To bleed air from the system:

•

Loosen the plug (3) of the fine filter (4).

•

Unscrew the handle (1) of the

hand-priming pump.

•

Check whether the fuel tank valve is

opened and whether there is fuel in the

tanks.

•

Loosen the plug (2) on the fuel pump.

•

Quickly purge the system with the boost

pump until clean fuel without air bubbles

emerges from the plug. Tighten the fuel

pump plug (2). Keep on purging the system

until without air bubbles emerges from the

fine filter plug (3). Tighten up the plug.

•

Screw the handle (1) of the

hand-priming pump.

Note:

If the engine start is difficult,

loosen in turn the captive nut (5) of each

injector fuel line, while cranking the

crankshaft to remove air from the lines.

Crank the crankshaft for 10 to 15

seconds for each line and tighten the

captive nut without stopping cranking. If

any disturbances are observed, loosen

and screw each nut with the engine

running.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды