Belarus 1221.2 Скачать руководство пользователя

Страница: 164 / 295

BELARUS-

1221.2/1221В.2/1221.3

Adjustments

163

External adjustment of PTO band brakes

Fig.

-6

1. Set PTO rod (1) to position «Off» (an

extreme lower position) as described in

the figure

-5.

2. Remove a bolt (13) and a plate (12) as

described in the picture

-6.

3. Using a wrench (S=14 mm) turn an ec-

centric control roller (3) clockwise by an

angle of about 30°.

4. Reinstall the plate and the bolt (13)

back.

Repeat the above-mentioned operations

until a specified distance «

» is obtained

for both PTO engaged and disengaged

modes.
If you fail to obtain a specified distance “A”

and a flat on the roller (3) moved from an

extreme right (normal) vertical position to

an extreme left one

do an internal ad-

justment of the PTO band brakes.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды