Belarus 1221.2 Скачать руководство пользователя

Страница: 86 / 295

BELARUS-1221.2/1221

.2/1221.3 Description and operation

Clutch control (BELARUS-1221

.2)

I. Forward run

The clutch is disengaged by stepping on

the pedal (1), Fig. E-

11а

acting upon the

operating cylinder (2) of the hydraulic

booster (6) and then upon the rod (9) and

lever (10) of the shaft of the clutch disen-

gagement forks. The hydraulic booster

reduces the efforts needed to press the

pedal when disengaging the clutch; also,

it controls the travel of the lever (10) in

proportion to that of the pedal.
On releasing the clutch pedal, all the

clutch control components return to their

initial position by the force of contracting

springs (4, 8). To operate the hydraulic

booster, a discharged oil flow is used

supplied from the HSU metering pump

through pipeline (12). After the hydraulic

booster the oil is drained in to the HSU

reservoir via the discharge oil pipeline

(11).
With the engine inoperative, the control

train functions as a mechanical one (Fig.

E-11).

Fig. E-

11а.

Clutch control of a reversible tractor:

1 – clutch pedal; 2 – operating cylinder with a rod; 3 – axle; 4, 8 – contracting spring; 5 – hose; 6 – hydraulic

booster; 7 – bracket; 9 – rod; 10 – lever; 11 – discharge oil pipeline; 12 – delivery pipeline; 13 – backward

spring; 14 – overhung pedal; 15 – pin; 16 – axle; 17 – boot; 18 – bracket; 19 – piston rod; 20 – piston; 21 –

master cylinder; 22 – oil pipeline; 23 – cap; 24 – overflow valve.

II. Reverse.

The hydrostatic drive consisting of an

overhung pedal (14) with backward spring

(13), master cylinder (21), oil pipeline

(22), and operating cylinder (2) with a rod

is used in this case.
The clutch is disengaged by means of the

pedal (14) which acts on the piston rod

(19) and piston (20) of the master cylin-

der. Under the action of the piston, the

fluid passing through the oil pipe (22) and

hose (5) causes the hydraulic booster (6)

pushrod to move and, thus, to release the

clutch in the manner described for the

forward run of the tractor. As this takes

place, the body of the service cylinder (2)

and the rod as well as the pedal (1) re-

main stationary in the initial position.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды