Belarus 1221.2 Скачать руководство пользователя

Страница: 115 / 295

BELARUS-1221.2/1221

.2/1221.3 Description and operation

114

The main gear.

The main gear is a pair of conical gear

members with helical teeth.

The axle drive gear 36 (fig.

-25) is in-

stalled in the pinion carrier 29 on two roller

conical bearings. Bearings preload is ad-

justed by means of adjusting washers 30,

after that bearings are tightened up by the

nut 33. The driven gear 19 is set on the

splines and a center pilot of the differential

casing 18 and is prevented from the axial

movement by the nut 20

The main gear mesh adjustment is pro-

vided by the gasket seals 28, 15, installed

between the driving gear cage flange and

FDA housing, and also between the left

and right arm supports and FDA housing,

respectively. Before the mesh adjustment,

the differential bearings are adjusted by

means of gasket seals 15.

The hole for the plug 25 serves for test-

ing the main gear mesh adjustment.

The outflow of oil from the main gear

and axle beam housing is prevented by

the collars and rubber rings, installed in

the fixed blocks, arm supports and in the

main gear pinion carrier.

To prevent affluent of oil in front of the

driving gear collar, the obturator ring 31 is

installed on its splined end. Spiral flutes

are threaded along the outer diameter. A

sleeve-type bearing with cross grooves is

installed in the fixed block 12.

Differential.

Differential – is a self-locking type with

enhanced friction. In the differential casing

1 (fig.

-26) and a cover 7 bolted together,

there are two pairs of planetary gears on

the floating axes 5, side gears 8, press-

on carriers 4 and friction disks – driving 2

and driven 3.

The self-locking differential automatically

connects both half-axes and excludes sepa-

rate wheels slipping, increasing the driving

force of the front wheels. The locking is car-

ried out when putting the front axle into oper-

ation.

Herewith the planetary gears shafts work

under load and move in the channels-

backfalls in the casing and cover of the diffe-

rential over a value of spacings between fric-

tion disks, respectively. The force is transmit-

ted from the axes to the planetary gears,

which transmit it to the carriers, and the car-

riers in their turn compress the friction disks

till they bear against the walls of the casing

and differential covers. Driving disks, having

outer cogs, are connected to the cogs of the

housing and differential cover, driven disks

(by inner cogs) – to the side gears. The fric-

tional force of the compressed disks units the

side gears and the housing with the differen-

tial cover, thus locking the differential.

When turning the tractor and when the

front axle is engaged and external forces

exceed the frictional forces in the frictional

disks, the frictional discs will slip.

The differential is installed on two roller

conical bearings in the brackets of front

axle beam. The differential bearings are

adjusted by the gasket seals 15 (fig.

25).

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды