Belarus 1221.2 Скачать руководство пользователя

Страница: 257 / 295

BELARUS-1221.2/1221V.2/1221.3 Scheduled maintenance

256

Operation 19. Lubricate the clutch

release yoke bearing

•

Remove the plug (1) from the left side of

the clutch housing.

•

Using a gun, make 4 to 6 injections of

Litol-24 grease through the lubricator

screwed into the housing of the release

yoke to lubricate the release bearing.

Note:

Do not inject excessive amounts of

grease, as excessive grease will

accumulate inside the clutch housing

and can get to the dry friction surfaces.

Operation 20. Turbocharger

Check tightening of fasteners of the

turbocharger (1), exhaust manifolds (3)

and exhaust pipe bracket (2). As

necessary, tighten the fasteners to a torque

of 35 to 40 N•m.

Operation 21. Front wheel toe-in

The front wheel toe-in must be within 0 to 8

mm. If necessary, perform adjustment

operations in accordance with the

recommendations in the section

“Adjustments”.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды