Belarus 1221.2 Скачать руководство пользователя

Страница: 192 / 295

BELARUS-

1221.2/1221В.2/1221.3

Aggregation

191

Towing drawbar TD-1

-01 (drawbar)

Implements: semi-trailers (the same as for a TD-2

and a

D-3

), trailers (the same as for

D-2

and a TD-3

Fig.

-10.

Towing drawbar

A clevis with a possibility of a position

change with reference to the PTO end

Distance between the clevis and a supporting surface,

442

Distance between the PTO end and connecting pin

axis, mm

390 or 490

Connecting pin diameter, mm

Vertical load on a TD, kN

Implement turning angle with reference to a tractor,
degrees

± 85

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды