Belarus 1221.2 Скачать руководство пользователя

Страница: 161 / 295

BELARUS-1221.

2/1221В.2/1221.3

Adjustments

160

Rear wheels tread setting

1. Jack up a rear part of the tractor until

the wheels are above the ground.
2. Remove the nuts (1) and take off the

wheels.
3. Loosen the clamping bolts (2) of the

upper and lower shells (3) of the wheel’s

hub by 2...3 turns.
4. Using four dismantling bolts which are

screwed into the upper and lower shells

(two bolts into each shell)

draw the shells

(3) out from the wheel’s hub in order to

release a bevel clamp and the wheel’s

hub for making the hub move.
5. Move the hub along the semi-axle to

obtain the required tread «L» (use a given

table for tread adjustment by measuring

the distance «

» from the end of the semi-

axle to the end of the shells).
6. Remove dismantling bolts and tighten

the bolts of the hub’s fastening.
7. Install the wheel and repeat the proce-

dure for the opposite rear wheel.

Tread adjustment when doubling the

rear wheels

To install the hubs (basic and additional

ones) of the external and internal wheels

relative to the semi-axis of the rear axle

and wheels disks,

follow Picture

-2.

Rear wheels tread is adjusted steplessly.

Fig.

-2.

Table

-2

Tread

«L»,

Distance

«К»,

Wheels installation

scheme

(for tires

11,2R42)

«А»

«Б»

245

1420

—

205

1500

—

155

1600

—

1800

—

1900

—

245

—

1950

220

—

2000

170

—

2100

Tread

«L»,

Distance

«К»,

Wheels installation

scheme

(for tires 18

4R38)

«А»

«Б»

1650

133

1800

200

222

2150

147

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды