Belarus 1221.2 Скачать руководство пользователя

Страница: 207 / 295

BELARUS-

1221.2/1221В.2/1221.3

Aggregation

206

3.12 Safety of tractor aggregation

To ensure the trouble-free operation of the tractor and aggregated machines as well as

to exclude accidents and emergencies, we recommend you to read carefully this Operat-

ing Manual for the tractor and follow strictly the recommendations contained herein at any

time. Please, observe strictly all the safety recommendations and accident prevention

regulations.

Failure to observe the accident prevention regulations can cause the threat for the life

and material damage due to breakdown of the tractor or aggregated machine and loss of

all the rights for the compensation for damages including that according to the warranties.

Do not risk your health or life due to failure to observe the accident prevention regulations.

The worker shall not be allowed to operate the tractor including aggregating the imple-

ments with it or performing its maintenance unless he/she has red and understood ALL the

guidelines concerning the operation of the tractor and accident prevention regulations.

Attention!

The operating documentation (concerning both the tractor and the aggregated machine)

shall be stored obligatorily in the cab so that it could be used in case of arising of any

questions during the work. If the Operating Manual for the machine or tractor is lost, ac-

quire a new one without delay.

Below are stated the accident prevention guidelines, which shall be observed rigorously

when aggregating the tractor with various machines, but are often unconsciously ignored

by you during the everyday use of the tractor and machines.

3.12.1 MOTION ON PUBLIC ROADS AND HAULING OPERATIONS

Actually for the half of the time of its operation, the tractor is used on transport commu-

nication driving on public roads. Therefore, the transport MTAs are subject to exclusive

safety standards. The vehicles such as tractor trailers or semitrailers shall be equipped

with service and parking brakes and safety chains (ropes). The load-carrying capacity of

the vehicles (trailers, semitrailers, fertilizer distributors and spraying machines) depends

on the relief of the locality, slope and condition of the roads. With the account of the allow-

able longitudinal slope of 12 degrees, the total weight of the semitrailer (trailer) equipped

with brakes shall not exceed 12000 kg and that on relatively flat area (with the slope of

less than 4%) with dry hard road pavement – not more than 15000 kg.
The tractor’s track value shall correspond to the conditions of the works to be per-

formed, technical characteristics of the tractor and ensure the safe use of the tractor within

machine-tractor aggregates. When driving the tractor on the slopes and sharp turns in-

crease the tractor’s track for increasing the stability.

The service brake actuator is made as a single-wire scheme which is controlled from

the workplace of the tractor operator. The parking brake actuator shall be located on the

machine.

Aggregation of the general-purpose vehicles (trailers and semitrailers) shall be made

through the towing drawbar TD-2 or

ТTD

З.

For the safety reasons, the coupling with the tow-

ing drawbar TD-

1Ж and

ТD

-1 is strictly forbidden.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды