Belarus 1221.2 Скачать руководство пользователя

Страница: 221 / 295

BELARUS-1221.2/1221

.2/1221.3 Possible defects and ways of their elimination

220

Defect, external manifestation

Way of elimination

Slipping of drive clutch

Check and regulate pressure in hydro sys-

tem of transmission (9...10 kilogram

force/sm

). Replace worn out disks.

Defects in electric line of front driving axle

control.

Determine and eliminate defects.

Insufficient size of torque being transferred by clutch because of oil leakage in hy-

dro system:

Deterioration of rubber sealing rings.

Replace rings.

Deterioration of piston rings and clutch drum; Replace rings.

Deterioration of interfaced surfaces “holder

– nave of drum”, “drum – piston”

Replace worn out details.

Drive of front driving axle does not work in automatic mode

Deterioration of adjustment or refuse from

switch of automatic switch-on gauge.

Adjust position of switch or replace it.

High noise and heating in zone of main gear

Gap in gears bearings of main gear.

Adjust bearings of gears.

Wrong gears engagement of the main gear.

Check and if it is necessary adjust interlock

on spot of contact.

Noise at maximum angle of wheels rotation

Wrong operation mode of front driving axle.

Front driving axle works in compulsory

mode.

Check mode of inclusion of FDA drive and

install switch in position “switched off” or

“automatic”.

Wrong limiting angle of wheels turn.

Check and adjust.

Bang in pivot at movement

Adjustment of pivots bearings is disturbed. Check and adjust.

Bang in front driving axle at sharp turn of wheels

Gaps in pins of steering draft and hydro cy-

linders of turn.

Check and adjust.

Dribbling of greasing through cuff of main gear flange

Deterioration and damage of flange cuff.

Replace worn out parts.

Dribbling of greasing through breathers of wheel reduction gears

Increased level of oil.

Check and adjust correct level.

Dribbling of greasing through cuff of main gear of wheel reduction gear.

Increased backlash in gears bearings.

Check and adjust.

Deterioration and damage of cuff.

Replace cuff.

Angular frictions of wheels

Axial backlash in bearings of wheel reduc-

er pivots.

Check and adjust.

Increased backlash in bearings of front

wheels.

Check and adjust backlash in flange bear-

ings.

Backlash in bearings of hydro cylinders of

hydrostatic steering.

Replace worn out details.

Increased deterioration and ply separation of front wheels tires

Adjustment of wheels convergence is dis-

rupted.

Adjust convergence as it is shown in sec-

tion “Adjustments”.

Inadequacy of air pressure in tires to rec-

ommended norms.

Maintain pressure in tires in accordance to

recommendations (see section “Aggrega-

tion”).

Front drive is constantly positively en- Check switch-on – switch-off of front driv-

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды