Belarus 1221.2 Скачать руководство пользователя

Страница: 70 / 295

BELARUS-1221.2/1221

.2/1221.3 Operating controls and instruments

Reversible station controls.

The additional reverse controls are

located at the rear side of the cab

as shown in the figure below:
1 - the clutch is disengaged when

pressing the pedal. Clutch en-

gagement takes place by pedal

release.

2 –steering wheel of tractor turning

(it is taken from the steering

column of forward motion (9)).

3 –brakes pedal. Both tractor

brakes and pneumatic drive of

trailer brakes are engaged by

depressing the pedal.

4 –foot throttle. Fuel feeding is in-

creased by pressing the foot

throttle.

5 – horn button.
6 –fuel delivery control lever. Ex-

treme rearward position (on re-

verse) corresponds to full fuel

delivery, extreme forward posi-

tion corresponds to engine

stopping.

7 –gearbox ranges selecting lever

(see pattern I).

8 –transmission speed control lever

(see pattern II).

9 –steering column of forward mo-

tion.

To adjust the tractor for reverse

operation, proceed as follows:

•

lock the standard brake pedals;

•

transfer the steering wheel to the

additional steering column. For that

purpose turn off the handwheel of

the steering wheel fixation, transfer

the steering wheel and fix it at the

required height;

•

turn the revolving seat for reverse

operations;

•

set the HPS switch cock to the

“reverse” position.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды