Belarus 1221.2 Скачать руководство пользователя

Страница: 97 / 295

BELARUS-1221.2/1221

.2/1221.3 Description and operation

Engine Starting Interlock

As a precautionary measure against the

engine starting when the range is

switched on, the tractor is equipped with a

special interlock device (Fig. E-15.7). The

interlock consists of a switch (8) located in

the transmission gearbox casing on the

left side, balls (6) and pins (7, 7

а).

On switching the range on, the interlock

mechanism opens the switch contacts and

breaks the circuit of the starter intermedi-

ate relay (1).

The shims (9) are provided to adjust the

instant of contact opening (9).

ATTENTION!

Before proceeding to

starting the engine, set the transmission

gearbox speed-range change-over lever

to its neutral position!

Fig. E-15.7. Diagram of interlocking the engine starting:

1 – starter; 2 – alternator; 3 – interlock relay; 4 – starter switch; 5 – starter relay; 6 – interlock mechanism

balls; 7 – pin; 7a – lock; 8 – unlock switch; 9 – adjusting shims; 10 – range switch-over dogs

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды