Belarus 1221.2 Скачать руководство пользователя

Страница: 280 / 295

BELARUS-1221.2/1221V.2/1221.3 Scheduled maintenance

279

Overall maintenance

Operation 55. Adjust oil pressure in the

engine lubricating system

If the oil pressure in the lubrication system

of a warmed-up engine at a rated

crankshaft speed is below 0.28 MPa (2.8

kgf/cm²), stop the engine and correct the

fault. Check tightness of the oil lines and

serviceability of the relief valve in the oil

filter. One way to increase the pressure is

adjustment of the relief valve, paper oil filter

in a special shop.

Operation 56. Adjust the relief valve of

the gearbox centrifuge

The valve (2) maintains an oil pressure in

the system of 0.9 to 1.0 MPa (9 to 10

kgf/cm²).
If the pressure drops below the specified

limit, adjust the valve (2) by installing

additional washers (5) between the spring

(3) and the plug (6).

IMPORTANT!

If the pressure drops

below 0.7 MPa (7.0 kgf/cm²), stop the

tractor and contact a technician.

The valve (7) maintains an oil pressure

before the rotor of the centrifuge. It must be

0.75 MPa (7.5 kgf/cm²).
The lubrication valve (12) is set for a

pressure of 0.2 ± 0.05 MPa (2.0 ± 0.5

kgf/cm²) and maintains the oil pressure in

the GB lubricating system. Adjust the

valves with the washers (9) and (11).

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды