Belarus 1221.2 Скачать руководство пользователя

Страница: 95 / 295

BELARUS-1221.2/1221

.2/1221.3 Description and operation

The

high-to-low reduction gear stage

switch-over mechanism

of the trans-

mission gearbox

(Fig. E-15.5) is

mounted on the gear-shift mechanism

cover and consists of a cylinder (11) fixed

on the axle (12), pusher (7) and lever (5)

mounted on the roller (4). The fork (16) is

connected with the lever (5) by means of

the pin (6). The lever of the roller (4)

meshes with the dog of the fork (18) (Fig.

E-15.1) and forces the synchronizer (26)

coupling to move as the roller rotates.

The position of lever (5) is adjusted by

changing the length of the pusher (7) with

further locking by a check-nut (8). The

cylinder (11) communicates with the hy-

draulic system through an electro-

hydraulic valve (14). The sensor (15)

connects the valve (14) to the electric cir-

cuit when the gear-shift lever is in its neu-

tral position, only. The drawn-in position

of the cylinder corresponds to the lower

“L” stage of the transmission gearbox re-

duction gear. Pressure-sensitive pick-ups

(10) serve to indicate the engaged state

of the reduction gear.

Fig. E-15.5. High-to-low reduction gear stage switch-over mechanism:

1 – gear-shift fork; 2 – speed range change-over fork; 3 – bolt; 4 – roller; 5 – lever; 6 – pin; 7 – pusher; 8 –

check-nut; 9, 13 – oil pipelines; 10 – pressure-sensitive pick-up; 11 – hydraulic cylinder; 12 – axle; 14 – elec-

tro-hydraulic valve; 15 – sensor, 16 – fork, 17 – bracket, 18 – adjusting screw.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды