Belarus 1221.2 Скачать руководство пользователя

Страница: 101 / 295

BELARUS-1221.2/1221

.2/1221.3 Description and operation

100

Automatic Differential Lock-Up (ADL)

The ABD feature is designed to improve

the tractor traction and adhesion proper-

ties and off-road capability. It consists of a

two-disk hydraulically operated lock-up

clutch (Fig. E-17) and an electro-hydraulic

control system. The latter ensures two op-

eration modes: “automatic” and “forced”.

Fig. E-18. Rear axle differential lock and FDA drive control system:

1 – control panel; 2 – steering wheel turning angle sensor; 3, 10 – control electro-hydraulic distributors for

the DL and the FDA drive, respectively; 4 – terminal blocks; 5 – connecting cable; 6 – DL control key; 7, 12 –

indicator lamps; 8 – loop; 9 – automatic FDA drive control sensor; 11 – FDA drive control key

The

electro-hydraulic DL control sys-

tem

of the rear axle (Fig. E-18) is com-

posed of a panel (1), turning angle sensor

(2) of steering wheels; installed on the left-

hand FDA reduction gear, DL control elec-

tro-hydraulic distributor (3) located on the

right-hand GB cover and coupled through

an oil pipeline with the DL clutch, and

connecting cables (5) with terminal blocks

(4). The system is supplied with power

from the on-board electrical circuit via a

safety fuse in the fuse box installed in the

dashboard. The system is powered after

starting the engine. The key (6) for con-

trolling the DL control and DL indicator

lamp (7) are installed on the panel (1)

face. The latter is located over the right-

hand side tractor control panel.

How to Use the Rear Axle DL Control

Key (6)

1. When performing jobs with great

amount of relative slippage of the rear

wheels, depress the upper part of the

key (6) (fixed position), thus, activating

the automatic mode of differential lock-

up. Now the electromagnet of the DL

control electro-hydraulic distributor (3)

is energized, the electro-hydraulic dis-

tributor spool valve moves and discon-

nects the lock clutch from the discharge

line and connects it with the feed port.

Then, the lock-up clutch operates and

interlocks the differential and the rear

wheels. The differential is unlocked

automatically when the steering wheels

turn to a certain degree.

2. If a short-time interlocking of the rear

wheels is necessary, including occa-

sions of turning, press the lower part of

the key (6) and hold it in this depressed

position. When released, the key (6) re-

turns to its middle, fixed position, and

differential interlock unlocks.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды