Belarus 1221.2 Скачать руководство пользователя

Страница: 156 / 295

BELARUS-1221.2/1221

.2/1221.3 Tractor preparing for operation

155

When a 6-splined shaft tail is replaced

with a 21-splined one, switch PTO drive

to 1000 rpm and run the engine at 2156

rpm to obtain standard PTO speed of

1000 rpm.

Warning!

To avoid unexpected move-

ment of the implement, disengage the

PTO after each use.

The PTO-driven equipment not requiring

high power take-off, must have 6-splined

coupling to run at 540 rpm. In this case it

is necessary to set 2037 rpm of the en-

gine.
The PTO-driven equipment which re-

quires high power take-off operates at

1000 rpm of PTO shaft tail and is pro-

vided with 21-splined coupling to be at-

tached to PTO shaft tail.

Two-speed PTO

switch position

Engine

speed

(rpm)

PTO

speed

(rpm)

Power mode

(6-splined, speed I, 82

h.p.)

2037

2100

540

556

High power mode (21-

splined,

speed II,123 h.p.)

2156

2100

1000

974

Changing PTO shaft tail

•

Remove two bolts and tail cap (2).

•

Unscrew four nuts (5), remove a

housing

(1) and a plate (4).

•

Remove six bolts, the plate and take

out the PTO tail (3).

•

Install the other PTO shaft tail into a

spline hole, mount the plate and all

other removed parts in a reverse order.

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды