Belarus 1221.2 Скачать руководство пользователя

Страница: 252 / 295

BELARUS-1221.2/1221V.2/1221.3 Scheduled maintenance

251

Operation 12. Check the engine air

cleaner

Check condition of the paper filter elements

(PFE) for presence of paper break and

correct installation of the PFE.
To check the basic filter element (BFE),

proceed as follows:

•

unscrew the butterfly nut (2) and remove

the pan (1);

•

unscrew the butterfly nut (3) and

remove the BFE (5);

•

check the monitor filter element (4) for

contamination without removing it from the

casing (6).

ATTENTION!

Removing the monitor

filter element (4) from the casing (6) is

not recommended.

Contamination of the monitor filter element

(4) indicates that the BFE is damaged (the

paper shutter broken, the bottoms

unstuck). In such a case, rinse the MFE

and replace the BFE.

Note:

In case of strong dust, perform the

Operation 12 every 20 hours of engine

operation.

Operation 12a. Check and tighten

fasteners of wheel hubs and nuts

Check the tightening torques and, as

necessary, tighten:

•

bolts (1) of the rear wheel hubs to a

torque of 360 to 500 N•m;

•

nuts fastening the rear wheels to the

hubs

―

300 to 350 N

•

nuts fastening the front wheels to the

flanges

―

200 to 250 N

•

nuts fastening the front wheel disks

to the rim brackets

―

180 to 240 N

•

Содержание 1221.2








































































































































































































































































































Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды

Belarus 1221.2, Руководство оператора

Результаты поиска

Содержание 1221.2

Отзывы:

Похожие инструкции для 1221.2

Бренды по названию

Популярные бренды