background image

Congratulations on being an owner of a versatile KIOTI DK55 tractor. This tractor has been designed with the finest

materials and under rigid quality control standards set forth by the KIOTI engineering department.

Knowledge of tractor operation is essential for many years of dependable service and reliability. This manual is

given to help you familiarize yourself with the DK55 tractor and to give you helpful information about tractor safety,

operation and maintenance. It is the policy of KIOTI  to provide each KIOTI  tractor owner with a detailed owner’s

manual to help you answer many questions. If the information you are seeking is not found in this manual, your

KIOTI tractor dealer will be happy to help you.

Please feel free to contact DAEDONG - USA,INC.

Throughout this manual, you will see text in italics, preceded by the words DANGER, WARNING, CAUTION or

IMPORTANT.

Such text has the following significance.

FOREWORD

SIGNS

DESCRIPTION

DANGER

WARNING

CAUTION

IMPORTANT

This mark indicates a hazardous situation which, if not observed, may result in death or
fatal injury.

This mark should be indicated for most dangerous situations only.

This mark indicates potentially hazardous situations which, if not observed, may result in
minor or moderate injury. And this mark can be used as a warning against unsafe
activities.

This mark indicates emphasis on notable characteristics in working procedures or infor-
mation on working procedures and technology for convenient use.

This mark indicates potentially hazardous situations which, if not observed, may result in
death or moderate injury.

Summary of Contents for DK55








































































































































Reviews: