manualshive.com logo in svg

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 100 / 252

Поделиться
Скачать
baxter Flo-Gard 6301 Скачать руководство пользователя страница 100

8

Disassembly/Reassembly

8-26

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

7.

Perform the Operational Checkout procedures in Chapter 10, 
“Operational Checkout”.

Replacement of CPU Board

1.

Separate front and rear housings in accordance with “Separation of Front 
and Rear Housings” on page 8-5.

2.

Separate boards in accordance with “Separation of Printed Circuit 
Boards” on page 8-7.

3.

Carefully squeeze the four board spacer tops (Figure 11-2 , item 10) with 
needle nose pliers to release the CPU board (Figure 11-2 , item 2) from 
the display board (Figure 11-2 , item 1).

4.

Lift the Pump 1 side of the CPU board to disconnect CNDISP at the 
bottom of the board from the display board and pull it perpendicularly to 
the board.

5.

Reassemble in reverse order. Be sure to check that the Pump 2 side of the 
CPU board in the slot of the white PCB holder on the display board and 
that the connector CNDISP is seated firmly. Be sure to remove any dirt 
or dust on the LCDs and the windows before tightening the CPU board 
to the front housing. Tightening torque for the board is 7 kg-cm 
(6.1 in-lb).

6.

Calibrate in accordance with “DC Line Voltage Calibration,” 9-1 through 
“Slide Shaft Sensor Calibration,” 9-18.

7.

Perform the Operational Checkout procedures in Chapter 10, 
“Operational Checkout”.

Replacement of Display Board 

1.

Separate front and rear housings in accordance with “Separation of Front 
and Rear Housings” on page 8-5.

2.

Separate circuit boards in accordance with “Separation of Printed Circuit 
Boards” on page 8-7.

3.

Stand the printed circuit cards upright and remove the five screws 
(Figure 11-2 , item 15) securing the corners and right center of the 
display board. 

4.

Carefully disconnect connector CNDISP and remove the display board 
from the sensor board. 

CAUTION

Be sure to place the CPU board on an insulated surface. Avoid touching 
potentiometers on the CPU board and the LCDs on the display board during the 
disassembly/assembly procedures.

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов