manualshive.com logo in svg

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 108 / 252

Поделиться
Скачать
baxter Flo-Gard 6301 Скачать руководство пользователя страница 108

8

Disassembly/Reassembly

8-34

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

4.

Tilt the device back and carefully pull the battery compartment (item 8) 
and cover.

5.

Remove the four screws (Figure 11-4 , item 26) that hold the battery 
compartment to the cover and disconnect the battery wires.

6.

Remove the EPROM(s) using an IC removal tool.

Note: 

The Master EPROM is located above the Slave EPROM (designated on the 
board). Also, note that the orientation of both EPROMs is with the notch 
toward the bottom of the PC board.

7.

Use an IC insertion tool to install the new version EPROM(s). Make sure 
that all of the pins are seated in the socket correctly, and that the notched 
ends of the EPROM(s) are pointed up.

8.

Replace the battery (“Replacement of Battery” on page 8-24).

9.

Connect the battery wires to the battery, ensure correct polarity, and slide 
the battery carefully into the battery compartment.

Note: 

W

hen the secondary alarm is activated, press the 

ON-OFF/CHARGE

 key to 

stop the alarm. If a failure code appears, perform steps 1-5 in “Modifying the 
Configuration Option Settings” on page 5-2.

10.

Set the configuration to its original settings per “Modifying the 
Configuration Option Settings” on page 5-2.

11.

Perform the Operational Checkout procedures in Chapter 10, 
“Operational Checkout”.

Pole Clamp Tightening Instructions

Note: 

These instructions must be performed during any service involving the IV pole 
clamp assembly. 

Note: 

W

hen servicing the pump ensure the pole clamp body is secured to the rear 

housing. In addition, all pumps being serviced must meet the requirements 
listed below.  An upgrade label with box number 2 marked indicates these 
requirements have already been met.

1.

Refer to Figure 11-4  “Rear Housing Assembly, External” to view the 
attachment of the pole clamp body to the rear housing.

a.

The recessed area in the housing for the pole clamp body must 
be clean.

b.

The three mounting screw holes in the housing must not show 
signs of cracking.

c.

The ground wire must be attached to the center screw.

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов