manualshive.com logo in svg

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 127 / 252

Поделиться
Скачать
baxter Flo-Gard 6301 Скачать руководство пользователя страница 127

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

9-17

Calibration

Verifying Calibration Values

11.

View the NORM value displayed in the PRI RATE location at the upper 
left of the main display.

12.

View the MIN value displayed in the PRI VTBI location at the lower left 
of the main display.  Both values must be less than 40.

Q

If they are within specification, proceed to the next step.

Q

If they are out of specification, perform the procedure in “Air Sensor 
Calibration” on page 9-6.

13.

Follow steps 14 through 18 to check that the tube misloading sensor 
outputs in SEC RATE and SEC VTBI windows are within specification.

14.

Load a Baxter “s” suffix standard administration set and prime it with 
fluid.

15.

With the pump door open, check the FSRR value (at SEC RATE 
window) and the FSRL value (at SEC VTBI window). Both values 
should display between 500 and 820.

16.

Repeat above step with the pump door closed. Both values should 
display between 500 and 820.

17.

Open the door and intentionally load the tubing over the tube misloading 
sensor 1L and/or 2L (Figure 11-6 , item 10).

18.

Close the door. Do not load hard components on the administration set 
between the door and the base plate. The FSRL value (at SEC VTBI 
window) should display 450 or less.

19.

Repeat above step on the tube misloading sensor 1R and/or 2R 
(Figure 11-6 , item 11). The FSRR value (at SEC RATE window) should 
display 450 or less.

Note: 

The sensors are normal when the values in steps 15 through 18 are within 
specification. 

W

hen any of these values are out of specification, replace the 

tube misloading sensor per “Replacement of Force Sensing Resistor (FSR) 
Devices for Tube Misloading Sensors” on page 8-15.

20.

Press the 

TIME

 key and check that the voltage Vcpu reading in the SEC 

RATE window of the display is within 472 - 579. Actual voltage = 
displayed data x 0.00976.

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов