baxter Flo-Gard 6301 Скачать руководство пользователя страница 46

Страница: 46 / 252

Preventive Maintenance

6-4

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

Schedule: Every 12 months or as required

Back plate and safety clamp

When the safety clamp or back plate

does not operate smoothly, clean or

replace in accordance with

“Replacement of Safety/Slide Clamp

Assembly” on page 8-19 or

“Replacement of Back Plate” on page

8-23.

Door latch area

Remove pump head door cover in

accordance with “Replacement of

Pump Head Door Cover” on page 8-9.
If Latch is cracked or loose replace in

accordance with “Replacement of

Pump Door Latch” on page 8-10.
If door is cracked in Latch area replace

in accordance with “Replacement of

the Pump Door or Pump Door

Assembly” on page 8-11.

Pole clamp

When operation is not smooth, apply

one drop of high grade general purpose

machine oil to the screw threads.

Power cord

Replace power cord when the pins are

bent or the insulation is damaged.

Preventive maintenance tests

Perform the tests detailed in Chapter

10, “Operational Checkout”.
Perform the calibration verifications

described in “Automatic Test Mode 1:

Calibration Mode 1” on page 9-14 and

“Automatic Test Mode 2: Calibration

Mode 2” on page 9-16.

Schedule: Every 6 months or as required

Battery check

Perform the Battery Check described

in Chapter 10, “Operational Checkout”

every 6 months after the first year

following battery installation/

replacement.

Table 6-2

Preventive Maintenance Procedures — continued

Check

Action

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 46 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: