baxter Flo-Gard 6301 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 252

baxter Flo-Gard 6301 Скачать руководство пользователя страница 57

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

7-11

Troubleshooting

Failure Identification Code Troubleshooting Table

Failure Identification Code Troubleshooting Table

Use Table 7-3 to determine the corrective action necessary to resolve failure
codes. The causes of each failure code are listed in the order in which they are
most likely to occur. Perform the corrective action items in the order in which
they are listed and retest the pump after each action. All replacement
procedures are contained in Chapter 9, “Calibration”.

There are two types of Failure Identification Codes: Alarm (codes 1-19) and
Failure (codes 20 and above). Alarm codes report malfunctions generally
correctable by the operator. Failure codes may require servicing of the pump.
A code of 0 indicates that less than 10 alarms/failures have occurred since the
log was cleared. The time and date are also 0.

Table 7-3

Failure Identification Codes

Code

Cause

Checks

Corrective Action

0

No alarms or failures.

No action necessary.

1

Air bubble detected in a Run

mode.

Check for air in tubing. Ensure set

is correct type and is properly

loaded. Ensure set tubing is not

scratched or deformed.

Expel air in tubing. Replace or

reposition set when tubing is

flattened or scratched. Clean air

sensor in accordance with Chapter

6, “Routine Maintenance” when

dirty.

Perform “Automatic Test Mode 2:

Calibration Mode 2” on page 9-16

steps 2 through 6.

When values are not within

specification, recalibrate or

replace the air sensor.

2
3

Downstream occlusion was

detected.

Check for scratched or deformed

tubing. Verify that solution and

ambient temperatures are between

60° and 100° F (15.5° and 37.7°

C). Ensure set is correct type and

is properly loaded. Check for

spilled solution in sensor region.

Remove downstream occlusion

and reposition the tubing. Clean

occlusion sensors in accordance

with “Cleaning” on page 6-1 when

dirty. Raise or lower temperatures

if necessary.

Perform “Automatic Test Mode 1:

Calibration Mode 1” on page 9-14,

steps 1 through 9.

Perform “Safety Slide Clamp

Mechanical Calibration” on page

«
...
55
56
57
58
59
...
»

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов