baxter Flo-Gard 6301 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 252

baxter Flo-Gard 6301 Скачать руководство пользователя страница 112

9

DC Line Voltage Calibration

9-2

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

4.

Connect an oscilloscope to Vmain (pin 6) or using a 0.1 mF capacitor
with the lead connected in series and the voltmeter set to AC verify the
ripple voltage:

Q

The ripple voltage should be

≤

100 mVp-p at 105 VAC.

5.

Connect the voltmeter to Vref (pin 1).

6.

Power up the pump.

7.

While both pumps are in STOP mode, the voltage should be 5.000
±0.050 VDC.

8.

Measure the Vcpu voltage at pin 3. The voltage should be 5.00
±0.30 VDC.

9.

Measure the Voth voltage at pin 4. The voltage should be 12.90 to
13.90 VDC.

10.

Measure the Vkey voltage at pin 5. The voltage should be 5.00
±0.30 VDC.

11.

Measure the lithium backup battery voltage at pin 7. It should be 3.0 to
3.4 VDC.

12.

Press the

ON-OFF/CHARGE

key to turn off the pump. Disconnect all

test equipment.

13.

Replace the battery cover.

14.

Calibration is not required when Vcpu voltage is within specifications.

Q

If the values are within specification, proceed to step 15.

Q

If the values are out of specification, calibrate the voltages using the
following procedure.

14.1

Connect the calibration circuit shown in Figure 9-1.

•

Variable transformer; 100 - 135 VAC, minimum 50 VA.

•

Digital voltmeter: 4.5 digits with ±0.1% accuracy at 20 VDC
range and ±3% accuracy at 100 - 135 VAC range.

•

DC ammeter: 2 ADC in 0.01 A increments.

•

Resistive load as shown in Figure 9-1

«
...
110
111
112
113
114
...
»

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов