manualshive.com logo in svg

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 135 / 252

Поделиться
Скачать
baxter Flo-Gard 6301 Скачать руководство пользователя страница 135

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

10-7

Operational Checkout

Air Alarm Test

Note: 

If INSERT SLIDECLAMP does not appear on the display, clean the slide 
clamp sensor with a cotton-tipped swab dipped in water and check the cali-
bration. If INSERT SLIDECLAMP still does not appear, replace the safety/
slide clamp assembly including the entire wiring assembly in accordance with 
Chapter 8, “Removal/Replacement Procedures”.

10.

Insert the clamp approximately one-third of the way into the mechanism. 

11.

Close the pump door. Verify that INSERT SLIDECLAMP appears on the 
display.

Note: 

If INSERT SLIDECLAMP appears on the display, clean the slide clamp 

 

sensor with a cotton-tipped swab dipped in water and check the calibration. If 
INSERT SLIDECLAMP still appears on the display, replace the safety/slide 
clamp assembly including the entire wiring assembly in accordance with 
Chapter 8, “Removal/Replacement Procedures”.

12.

Open the pump door and remove the tubing from the pump.

13.

Repeat this procedure for the other pump.

Air Alarm Test

The air bubble size for air detection is selectable through the configuration 
option and is factory set to NORM. See Chapter 5, “Configuration Option 
Feature” for an explanation of the configuration option. If the pump fails to 
detect air or if air detection is too sensitive, remove the pump from service 
and troubleshoot it in accordance with Chapter 7, “Troubleshooting”. Repair 
and recalibrate in accordance with Chapter 8, “Removal/Replacement 
Procedures”. Perform this test to verify air detection.

1.

Prime and load a Baxter “s” suffix standard administration set with one 
Y-site above the pump. Follow “Administration Set Preparation” on page 
10-2, steps 1 through 6.

2.

Using a precision gas-tight syringe, introduce an air bubble into the 
administration set through the Y-site above the pump. Verify that the 
pump detects air bubbles properly, depending on the bubble volume as 
shown in the table below:

Air Sensor 

Configuration

Test Air Bubble Volume 

(microliters)

Recommended 

Syringe (or 
equivalent)

No Alarm

Alarm

NORM

50

110

Hamilton #1725

MIN

25

85

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов