baxter Flo-Gard 6301 Скачать руководство пользователя страница 73

Страница: 73 / 252

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

7-27

Troubleshooting

Troubleshooting Chart

Inaccurate delivery: Accuracy

Check administration set for proper

type and code.
Check position and seating of the

tubing. Check that ambient and

solution temperatures are between 60°

and 100° F (15.5°and 37.7° C).
Check for cracks in the door hinges.
Check for deformation of the coil

springs of the back plate. Press back

plate in and out and ensure range of

motion.
Check for worn cams and pumping

fingers.
Remove front cover. Check for

damaged or deformed door latch or

damaged latch area.

Replace with Baxter "s" suffix

standard administration set if required.
Position tubing properly, without

stretching or slack.
Raise or lower the temperatures.
Replace the pump head in accordance

with “Replacement of Pump Head

Assembly” on page 8-12.
Replace the springs if required.
Replace worn parts as required.
Replace door latch in accordance with

“Replacement of Pump Door Latch”

on page 8-10.
Replace door in accordance with

“Replacement of the Pump Door or

Pump Door Assembly” on page 8-11.

Operational Issues

A FLOW RATE or CHECK VTBI

alarm occurs when a START key is

pressed.

Check that the rate or VTBI are within

the limits set by the configuration

option.

Change the maximum rate and/or

maximum VTBI setting through the

configuration option.

All front panel keys other than

BACKLIGHT

and

TOT VOL/

STATUS

are disabled.

Does Loc appear in the Main Display?

Press and release PANEL LOCK

switch on the rear panel. Loc in the

Main Display should disappear.

One or more front panel keys are not

accepted.

Check if the front panel is locked (Loc

appears in Main Display).
Turn pump off and back on and try the

key again.
Check front panel ribbon cable for

proper connection and continuity.

Press the PANEL LOCK switch to

remove the panel lock.
Replace front panel film.
Replace Sensor board.
Replace Display board.

The interval between audible alarm

tones is too long.

N/A

Change the interval for alert and/or

alarm tones to the desired value

through the configuration option.

Table 7-4

Troubleshooting Chart — continued

Symptom

Checks

Corrective Action

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 73 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: