baxter Flo-Gard 6301 Скачать руководство пользователя страница 24

Страница: 24 / 252

Controls and Indicators

2-4

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

16.

PRI VTBI

Key

Allows programming of the primary VTBI.

17.

PRI START

Key

Starts the primary infusion.

18. Plug Icon

Green LED, always lit while the pump is plugged in and the battery is charging.

19. MONITOR Legend

Lights for at least 2 seconds each time the host computer communicates with the

pump when the pump is in monitor mode.

20. Battery Icon

Yellow LED, always lit while the pump is operating on battery power.

21. COMPUTER CONTROL

Legend

Flashes when the pump is initiating communications with a host computer to enter

the computer control mode. It is constantly illuminated when the pump is in

computer control mode.

22.

CLR

Key

Clears any locked in values and programming values currently being entered.

23.

SEC START

Key

Starts the delivery of the secondary solution.

24.

SEC VTBI

Key

Allows programming of the secondary VTBI.

25.

SEC RATE

Key

Allows programming of the secondary infusion rate.

26. Numerical Keypad

The numerical values for rate, VTBI, and time are entered with these keys.

27. OPTIONS Key/Legend

Enables the device to operate in special modes.

Item

Function

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 24 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: