baxter Flo-Gard 6301 Скачать руководство пользователя страница 132

Страница: 132 / 252

Self Test

10-4

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

DURING SELF TEST:

•

The Main display turns off until the end of self test.

•

The Message display sequence is as follows:

•

Hospital Area Designator (active if the pump is

configured with options 1-9)

•

OCCLUSION LEVEL 1, 2, or 3

•

AUDIBLE SWITCHOVER if configured ON

•

AUTO RESTART (active if the pump is configured with

options 1-9 and flow check is configured ON)

Note:

If the INSERT SLIDECLAMP message appears, it means that one or more
sensors indicate that a tube is present and the on/off slide clamp is not. Stop
testing and verify the following:

•

No tube is in the pump.

•

The upstream occlusion sensor button is not siezed or
sticking.

•

The upstream occlusion calibration in Test Mode 1 is within
specification.

•

The air sensor "no tube" readings are within specification.

AT THE END OF SELF TEST:

•

The Main display should show the following:

Note:

Non-zero PRI and/or SEC rates and VTBIs may appear if still retained in the
five hour memory.

•

The Message display should show the following:

•

BATTERY LOW alarm must not be activated.

•

The battery icon must be lit.

Power on the other pump. Verify all that all segments of the Main
Display LEDs are lit.

Reconnect the device to AC power. Verify that the plug icon is lit and
that the battery icon is OFF.

PRI RATE (ML/HR)

PRI VOLUME (ML)

TO BE INFUSED

STOPPED

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 132 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: